Emerson | Firetrol FTA556E XG Jockey Pump Controller


PRODUCTS

Emerson Network Power > EMEA > Products > By Type > Fire Pump Controllers > Jockey XG Pump Controllers > Firetrol FTA556E XG Jockey Pump Controller

Firetrol FTA556E XG Jockey Pump Controller

Utilizing across the line, full voltage starting the FTA556E is the preferred controller whenever the utility or emergency generator set will permit this type of starting because of this low cost method. They are used for pressure maintenance in fire pump installations to prevent unnecessary cycling of the main fire pump.
Product Information/Sales
Overview

Firetrol® FTA556E XG Jockey Pump Controllers are intended for use with fire pump systems. They are used for pressure maintenance in fire pump installations to prevent unnecessary operation of the main fire pump.

Firetrol Jockey Pump Controllers are listed by Underwriters’ Laboratories, Inc., in accordance with UL508A, Standard for Industrial Controls, and CSA, Standard for Industrial Control Equipment. They are built to meet or exceed the requirements of the approving authorities as well as NEMA and the latest edition NFPA 70, National Electrical Code.

Features

Standard Features—The following are included as standard with each controller:

  • NEMA Type 2 (IEC IP22) Painted Steel Enclosure
  • Circuit Breaker
  • Horsepower rated motor starters
  • Suitable for use as service equipment
  • HAND-OFF-AUTO selector switch
  • Minimum run timer
  • On-Delay timer
  • Pump Restart Timer
  • Control circuit transformer with 24VAC secondary
  • 0-300 psi (0-20.7 bar) stainless steel solid state pressure transducer
  • Overpressure indication
  • Low Pressure indication
  • Failed to start indication
  • Main switch not in "Auto" alarm
  • Pressure recording
  • Event log (3000 events stored in controller memory)
  • Data log (including cycle counter)
  • Door mounted display/user interface featuring a 128 x 64 pixel backlit LCD Graphical Display, Membrane Type User Controller Push-buttons and LED indication for:
    • Power ON
    • Pump Running
    • Alarm
  • 2 lines of user selectable display information
Options/Modifications
SPECIAL ENCLOSURES
-T NEMA Type 3R (IEC IP22)
-E NEMA Type 4 (IEC IP66)
-F NEMA Type 4X (IEC IP66)*
-FXP NEMA Type 4X (IEC IP66), #304 Stainless Steel, Painted Finish
-FD NEMA Type 4X (IEC IP66), #316 Stainless Steel, Unfinished**
-FDB NEMA Type 4X (IEC IP66), 12 Gauge, Seam Welded, #316 Stainless Steel, Polished and Brushed Finish
-FDP NEMA Type 4X (IEC IP66), #316 Stainless Steel Painted Finish
-G NEMA Type 12 (IEC IP54)
**Unfinished (Not painted, polished or brushed)
HIGHER SHORT CIRCUIT CURRENT RATING
(See selection data sheet)
Fusible Disconnect Switch with Fuses (200kA)
ANTI-CONDENSATION SPACE HEATERS1
-H 120 Volt Space Heater
-J 120 Volt Space Heater With Thermostat
-K 120 Volt Space Heater With Humidistat
-L 240 Volt Space Heater
-M 240 Volt Space Heater With Thermostat
-N 240 Volt Space Heater With Humidistat
1 Power source supplied by others
PRESSURE TRANSDUCERS
-B 0-600 psi (0-42.25 bar) Pressure Transducer for Fresh Water Service
-C 0-300 psi (0-21.1 bar) Pressure Transducer for Corrosive Service
-D 0-600 psi (0-42.25 bar) Pressure Transducer for Corrosive Service
MISCELLANEOUS
-AC Contacts for Remote Indication, Pump Run
-AG Audible and Visible Low Reservoir alarm
-AM Contacts for Remote Indication, Failed to Start
-AST Auto Start Contacts (for connection to user supplied N.O. remote starting device)
-AW Contacts for Remote Indication, Reservoir Low (Requires option -AG)
-BW Contacts for Remote Indication, Phase Failure/Reversal
-BY Contacts for Remote Indication, Pump Overload
-CPL Contacts for Remote Indication, System Overpressure
-EF Contacts for Remote Indication, Switch Not in Auto
-HV Audible Alarm (required if local audible alarm indication is desired)
-IEC CE Marking with Externally Mounted Wet Parts
-IECI CE Marking (Internal Wet Parts)
-KH Contacts for Remote Indication, Common Output for Any Alarm
-NZ Interlock Input Contacts to Prevent Jockey Pump from Starting During Main Controller Operation
-OSP OSHPD Seismic Certification (State of California) (Requires option -SEI)
-PE Contacts for Remote Indication, Low System Pressure (Pump On Demand)
-S Tropicalization
-SEI Seismic Certifi cation (in accordance with IBC)
-ZPA Customized, annual service display message (when factory programmed or programmed by Firetrol representative during start-up)
-ZPJ Communications, Serial Modbus over RS485, 2 or 4 wire
*Export Packaging available for additional cost

NOTE: For requirements not listed here, please contact your Firetrol representative or the factory.

Product Information/Technical
Diagrams and Drawings
 
Technical Information

Firetrol Service Support

Keep mission-critical Firetrol Systems running at optimal levels.
+1 919 462 7105 24 x 7 x 365 respon​se

Learn More
​​